9mm or .40 S&W: what SAAMI, Glock and the makers print for each
Quick answer: SAAMI's ANSI/SAAMI Z299.3-2022 standard lists the same transducer maximum average pressure for standard 9mm Luger and 40 S&W: 350 in its psi/100 column, which is 35,000 psi. It lists 9mm Luger +P higher, at 385 (38,500 psi). The 40 S&W fires the wider bullet: SAAMI gives .4005 in against .3555 in for 9mm Luger. In each maker pair we read from one product line, the 40 S&W load lists the heavier bullet and more muzzle energy from a 4 in test barrel. Speer's 2025 catalog prints its 165 gr 40 S&W Gold Dot Personal Protection load at 484 ft-lb and its 124 gr 9mm load at 364 ft-lb. In the G19 and G23 Gen5 pair, the .40 version holds 2 fewer rounds: Glock lists 15 standard for the G19 Gen5 and 13 for the G23 Gen5. In the G26 and G27 pair the gap is 1 round. Glock lists the .40 slide at 27.5 mm wide against 25.5 mm, and the G23 Gen5 at 756 g with an empty magazine against 670 g for the G19 Gen5. Glock describes .40 S&W as having more recoil; no maker we read publishes a measured recoil figure. Decide on capacity, weight and the pistol you shoot well. Parts and holsters are listed by exact model and generation.
SAAMI gives the two standard cartridges one transducer pressure limit. The differences Glock prints are in the pistol: in each Glock Gen5 pair, the .40 model holds fewer rounds, has a wider slide and weighs more.
Cartridge names and SAAMI dimensions
SAAMI, the Sporting Arms and Ammunition Manufacturers' Institute, names the cartridges 9mm Luger and 40 Smith & Wesson, abbreviated 40 S&W. Its 9mm Luger drawing also carries the 9mm Luger +P. The European body C.I.P. calls the first one 9 mm Luger, with 9 mm Para(bellum) and 9 x 19 (mm) as alternative names. It calls the second one 40 S.& W. and prints no alternative name for it.
| Item | 9mm Luger | 40 S&W |
|---|---|---|
| SAAMI name | 9mm LUGER / 9mm LUGER +P (one drawing for both) | 40 SMITH & WESSON [40 S&W] |
| C.I.P. name | 9 mm Luger; alternative names 9 mm Para(bellum), 9 x 19 (mm) | 40 S.& W.; no alternative name printed |
| Bullet diameter (SAAMI) | .3555 - .0030 in (9.030 - 0.076 mm) | .4005 - .0030 in (10.173 - 0.076 mm) |
| Case length (SAAMI cartridge drawing) | .754 - .010 in (19.15 - 0.25 mm) | .850 - .010 in (21.59 - 0.25 mm) |
| Cartridge overall length (SAAMI) | 1.000 in (25.40 mm) minimum to 1.169 in (29.69 mm) maximum | 1.085 in (27.56 mm) minimum to 1.135 in (28.83 mm) maximum |
| SAAMI drawing first issued, last revised | 05/29/1979, revised 06/23/2021 | 02/01/1990, revised 07/09/2021 |
| Country of origin printed by C.I.P. | DE | US |
SAAMI's drawing for 40 S&W was first issued on February 1, 1990, and its 9mm Luger drawing on May 29, 1979. Those are the dates of SAAMI's drawings, not the dates the cartridges first appeared, and SAAMI prints no designer on either drawing. C.I.P.'s sheets print the same metric figures: 19.15 mm and 29.69 mm for 9 mm Luger, and 21.59 mm and 28.83 mm for 40 S&W.
Pressure: the same SAAMI limit for standard loads
SAAMI prints its transducer pressures divided by 100. In its calibration list, in the column headed MAP (psi/100), 9mm Luger and 40 Smith & Wesson both read 350, which is 35,000 psi. The 9mm Luger +P reads 385, which is 38,500 psi. MAP stands for maximum average pressure, which SAAMI defines as the recommended maximum pressure level for loading commercial sporting ammunition. SAAMI calls the piezoelectric transducer its preferred system.
In SAAMI Z299.3-2022's list of cartridge names, 9mm Luger +P carries an asterisk. The note it points to reads: "This ammunition is loaded to a higher pressure, as indicated by the +P marking on the case headstamp, to achieve higher velocity. Use only in firearms especially designed for this cartridge and so recommended by the manufacturer." SAAMI's standard has no +P+ entry.
SAAMI's Z299.3-2022 standard has no +P entry for 40 S&W. By the crusher method, in a column headed CUP/100, SAAMI lists 330 for 9mm Luger. It marks the crusher values for 9mm Luger +P and for 40 S&W as N/E, which its table spells out as Not Established. Psi and CUP come from different methods and are not one scale.
The European body C.I.P. lists its own figure, Pmax, in bar, measured by transducer: 2350 bar for 9 mm Luger and 2250 bar for 40 S&W. C.I.P.'s bar figures and SAAMI's psi figures come from two systems and are not converted into each other here.
Some comparisons say the 40 S&W runs at a higher pressure than the 9mm. SAAMI lists the same 350 for both standard cartridges and a higher figure for 9mm Luger +P. C.I.P. lists 40 S&W below 9 mm Luger.
Velocity and energy: SAAMI's reference table and maker pairs
SAAMI's reference table lists one or more nominal velocities per bullet weight, measured 15 feet from the muzzle of a 4.000 in test barrel for both cartridges. It names no brand or load. For a 124 gr 9mm Luger bullet SAAMI lists four reference velocities, from 1,030 to 1,170 fps. For a 180 gr 40 S&W bullet it lists one, 985 fps. For a 165 gr 40 S&W bullet it lists three: 980, 1,040 and 1,135 fps. SAAMI adds its own warning: "there should be no expectation that these velocities can be duplicated from any test utilizing firearms."
The ammunition makers print muzzle figures for their own loads. Each pair comes from one maker's product line. The page or catalog used for each row prints a 4 in test barrel for both loads; the Gold Dot G2 note shows where Speer's web page prints 5 in:
| Maker and line | 9mm Luger load, as printed | 40 S&W load, as printed | Note |
|---|---|---|---|
| Federal Personal Defense HST (jacketed hollow point) | P9HST1S, 124 gr: 1150 fps, 364 ft-lb, 4 in test barrel. P9HST2S, 147 gr: 1000 fps, 326 ft-lb, 4 in | P40HST1S, 180 gr: 1010 fps, 408 ft-lb, 4 in test barrel | Bullet weights differ |
| Federal American Eagle (full metal jacket) | AE9AP, 124 gr: 1150 fps, 364 ft-lb, 4 in test barrel | AE40R1, 180 gr: 1000 fps, 400 ft-lb, 4 in test barrel | Bullet weights differ |
| Speer Gold Dot Personal Protection (Gold Dot hollow point), 2025 catalog | 23614GD, 115 gr: 1210 fps, 374 ft-lb. 23618GD, 124 gr: 1150 fps, 364 ft-lb. Both 4 in test barrel | 23970GD, 165 gr: 1150 fps, 484 ft-lb. 23962GD, 180 gr: 1025 fps, 420 ft-lb. Both 4 in test barrel | Bullet weights differ |
| Speer Gold Dot G2, 2025 catalog | 24226, 147 gr: 1020 fps, 340 ft-lb, 4 in test barrel | 23999, 180 gr: 1015 fps, 412 ft-lb, 4 in test barrel | Speer's web page for 23999 prints a 5 in test barrel; the catalog prints 4 in |
| Speer Gold Dot Carry Gun, 2025 catalog | 24260, 135 gr: 1120 fps, 376 ft-lb, 4 in test barrel | 24259, 165 gr: 1150 fps, 484 ft-lb, 4 in test barrel | Bullet weights differ |
| Speer TMJ, 2025 catalog | 53824, 124 gr TMJ round nose: 1090 fps, 327 ft-lb, 4 in test barrel | 53982, 165 gr TMJ flat nose: 1050 fps, 404 ft-lb, 4 in test barrel | Bullet weight and nose shape differ |
| Hornady Critical Duty (FlexLock) | 90236, 135 gr: 1010 fps, 306 ft-lb, 4 in test barrel | 91376, 175 gr: 1010 fps, 396 ft-lb, 4 in test barrel | Bullet weights differ |
| Hornady Critical Defense (FTX) | 90250, 115 gr: 1135 fps, 329 ft-lb, 4 in test barrel | 91340, 165 gr: 1045 fps, 400 ft-lb, 4 in test barrel | Bullet weights differ |
Speer's catalog says: "Test barrels are used to determine ballistic figures. Individual firearms may vary." Glock lists the barrel of the G26 Gen5 and the G27 Gen5 at 87 mm (3.43 inch), while every maker figure above comes from a 4 in test barrel. In the text after its warning, SAAMI names "discrepancies in barrel length" as a further reason its test-barrel velocities should not be expected from firearms.
As printed, the 40 S&W load in every pair above has the heavier bullet and the higher muzzle energy. Muzzle velocity does not follow one side. Speer lists its 165 gr 40 S&W Gold Dot Carry Gun at 1150 fps and its 135 gr 9mm at 1120 fps. Federal lists its 124 gr 9mm HST at 1150 fps and its 180 gr 40 S&W HST at 1010 fps.
Some answers online say the 40 S&W delivers about twice the energy of the 9mm. The printed rows do not show that. Federal lists 408 ft-lb for its 180 gr 40 S&W HST and 364 ft-lb for its 124 gr 9mm HST. Speer lists 484 ft-lb for its 165 gr Gold Dot Personal Protection load and 364 ft-lb for its 124 gr one. Every figure comes from a 4 in test barrel.
40 caliber vs 9mm in one pistol: Glock's Gen5 pairs
Each Glock Gen5 pair here sets a 9mm model beside a .40 S&W model. Within each pair Glock lists the same barrel length and overall length. The overall width matches too. Glock notes that its technical data are rounded and do not reflect tolerances.
| Glock model | Caliber | Barrel | Length | Width | Slide width | Height incl. magazine | Weight without magazine | Weight with empty magazine | Standard capacity |
|---|---|---|---|---|---|---|---|---|---|
| G19 Gen5 | 9mm (9x19) | 102 mm (4.02 inch) | 185 mm (7.28 inch) | 34 mm (1.34 inch) | 25.5 mm (1.00 inch) | 128 mm (5.04 inch) | 610 g (21.52 oz) | 670 g (23.63 oz) | 15 |
| G23 Gen5 | .40 S&W | 102 mm (4.02 inch) | 185 mm (7.28 inch) | 34 mm (1.34 inch) | 27.5 mm (1.08 inch) | 129 mm (5.08 inch) | 687 g (24.23 oz), Glock's European page | 756 g (26.67 oz) | 13 |
| G17 Gen5 | 9mm (9x19) | 114 mm (4.49 inch) | 202 mm (7.95 inch) | 34 mm (1.34 inch) | 25.5 mm (1.00 inch) | 139 mm (5.47 inch) | 630 g (22.22 oz) | 708 g (24.97 oz) | 17 |
| G22 Gen5 | .40 S&W | 114 mm (4.49 inch) | 202 mm (7.95 inch) | 34 mm (1.34 inch) | 27.5 mm (1.08 inch) | 140 mm (5.51 inch) | 732 g (25.82 oz) | 806 g (28.43 oz) | 15 |
| G26 Gen5 | 9mm (9x19) | 87 mm (3.43 inch) | 163 mm (6.42 inch) | 33 mm (1.30 inch) | 25.5 mm (1.0 inch) | 106 mm (4.17 inch) | 559 g (19.72 oz) | 615 g (21.69 oz) | 10 |
| G27 Gen5 | .40 S&W | 87 mm (3.43 inch) | 163 mm (6.42 inch) | 33 mm (1.30 inch) | 27.5 mm (1.08 inch) | 107 mm (4.21 inch) | 621 g (21.91 oz) | 676 g (23.85 oz) | 9 |
The G23 Gen5 holds 13 rounds standard and the G19 Gen5 holds 15. The G22 Gen5 holds 15 and the G17 Gen5 holds 17. In the G26 and G27 pair the gap is one round: 10 in the 9mm G26 Gen5 and 9 in the .40 G27 Gen5.
Each .40 S&W slide is 27.5 mm wide as Glock lists it, 2 mm wider than the 25.5 mm slide of its 9mm twin. The .40 model is the heavier pistol in every pair, with or without the magazine. With an empty magazine, Glock lists the G23 Gen5 at 756 g and the G19 Gen5 at 670 g, 86 g apart.
Glock's European page calls the G23 Gen5 its compact 40 S&W, "equivalent of the GLOCK 19 Gen5". The two spec tables still differ in slide width, height and weight. The G23 Gen5 weight without a magazine, 687 g, comes from that European page; the empty-magazine weight of 756 g also appears on Glock's US page for the G23 Gen5 MOS.
Springfield Armory lists its XD 4" Low Capacity pistol in both calibers: SKU XD9101 in 9mm at 28 oz and SKU XD9102 in .40 S&W at 30 oz. Springfield does not say whether either weight includes a magazine. Both ship with two 10-round magazines, so this pair shows no capacity gap. Both are listed at 7.3" long and 5.5" high, with a 1.2" grip width. The barrel twist differs: 1:10 for the 9mm and 1:16 for the .40.
Smith & Wesson's law-enforcement-only full-size M&P M2.0 listings show a two-round gap: 17 for the M&P9 M2.0 (SKU 13615) and 15 for the M&P40 M2.0 (SKU 13083). Both list a 4.25 in barrel and a 7.4 in length. Both are listed at 5.5 in high.
Some comparisons say a 9mm pistol always holds two more rounds. In Glock's G26 and G27 Gen5 pair the gap is one, and in Springfield's XD 4" Low Capacity pair it is none. In the full-size Glock and Smith & Wesson pairs on our 9mm vs 45 ACP comparison, the gap against a .45 is wider: 17 against 13, and 17+1 against 10+1.
Does .40 S&W recoil more?
Glock USA's caliber glossary describes .40 S&W as "Larger and slower than 9mm, with more recoil." Its 9mm entry says the caliber "is the most popular and widely used worldwide" and makes no recoil statement. Glock's wording is a description, not a measurement. No maker we read publishes a measured recoil figure for either cartridge, and published comparisons give recoil percentages that disagree with each other.
What Glock does print is weight. In each Gen5 pair, the .40 S&W pistol is listed heavier. None of our sources measures how weight changes felt recoil, so no figure links the two.
None of our sources measures either cartridge for a first pistol, for hand size or for follow-up shots. Within each Glock Gen5 pair, Glock lists the same overall length and overall width, so the practical test is to shoot the 9mm and .40 versions of the same model before choosing. For a cartridge with a shorter case and a lower SAAMI pressure limit than either, see our 380 vs 9mm comparison.
Is .40 S&W harder on the pistol?
None of the maker sources we read publishes a wear, frame-life or parts-life figure by caliber. Glock's instructions for use cover its 9mm and .40 S&W models in one book, with the G22 and G23 in its specification pages. Its cleaning and lubrication schedule names no caliber, and its last item is "at least once a year."
Penetration and the FBI
A November 1989 FBI Law Enforcement Bulletin article, "The FBI's 10mm Pistol", describes FBI tests of handgun ammunition in 10% ballistic gelatin. Its bullet performance criteria list 12 inches of penetration as the minimum acceptable and 18 inches as the maximum desirable. The article adds: "It should be noted that no maximum penetration standard was established." The article does not mention 40 S&W.
The 1989 tests used three specific loads. The 9mm load was Winchester's 147 grain subsonic hollow point. The .45 load was Remington's 185 grain hollow point. The 10mm load was a 180 grain hollow point bullet the FBI handloaded to 950 feet per second. The test barrels were 4 in for the 9mm and 6 in for the 10mm and the .45. The tests ran eight events, from bare gelatin at 10 feet to auto glass at 20 yards; heavy clothing and plywood were among them. With those loads, 39 of 40 10mm shots met the 12 inch minimum. So did 37 of 40 .45 shots and 27 of 40 9mm shots. The article's conclusion: "The best performing round within the parameters of the FBI's test protocol was the 10mm."
Some comparisons describe a required 12 to 18 inch window. The 1989 article set 12 inches as a minimum and called 18 inches the maximum desirable, with no maximum standard.
Speer's 2025 catalog prints a gelatin and barrier table for two Gold Dot G2 loads: a 147 gr 9mm Luger load at 990 fps and a 180 gr 40 S&W load at 1000 fps. Speer does not state barrel length, distance or gelatin type for this table. Each cell gives penetration, then expansion:
| Test event (Speer) | 9mm Luger 147 gr Gold Dot G2 | 40 S&W 180 gr Gold Dot G2 |
|---|---|---|
| Bare gelatin | 14 in; 0.635 in | 15 in; 0.625 in |
| Heavy clothing | 14.5 in; 0.629 in | 15.75 in; 0.675 in |
| Wallboard | 14.5 in; 0.581 in | 13.5 in; 0.642 in |
| Plywood | 13.75 in; 0.575 in | 13.25 in; 0.672 in |
| Steel | 15.25 in; 0.483 in | 14.5 in; 0.568 in |
| Glass | 13.75 in; 0.533 in | 13.75 in; 0.598 in |
Speer lists 100% retained weight for both loads in five events and 85% through glass. The catalog's ballistics table lists the same two loads at 1020 fps and 1015 fps from a 4 in test barrel, so the gel table's velocities are a separate figure.
According to a Hornady press release dated October 11, 2017, the FBI awarded an IDIQ agreement for Critical Duty 40 S&W 175 gr FlexLock ammunition. A Hornady release dated April 26, 2018 says its Critical Duty 9mm+P "is the new handgun service ammunition of the FBI", and that this contract is in addition to the 40 S&W contract awarded in 2017. No FBI document we checked says which service pistol caliber the FBI chose after its 1989 10mm decision, or why.
Triggers and converting a .40 Glock to 9mm
TriggerTech says its Certified Special ACE trigger is "Compatible with Glock Gens 1-5* in standard frame 9mm and .40 S&W only." Its model list includes the 19 and the 23. The asterisk note reads "Gen 5 requires removal of small tab on the frame". The same page says "Not compatible with Gen V and Gen 6." Makers use "Gen V" differently: Timney's Gen 5 page calls its Gen 5 trigger "Compatible with the NEW Glock Gen V models". Check the list against the exact model name of your pistol.
Apex lists its Action Enhancement Trigger for Gen 3 and Gen 4 Glocks, with the Glock 19 (G19) and Glock 23 (G23) in both lists. The same page says "Not for use in Gen 5 models". A review published on Timney's site lists the Alpha Gen 3-4 kit for "All 9/40/357sig stock Glocks". For the Gen 5 Alpha, Timney's own product page lists "Calibers: 9 mm & .40 S&W", while that review lists its Gen 5 kit for 9mm Gen 5 Glocks only. Check Timney's fit list for your exact model and generation. Our Glock trigger roundup includes the Timney Alpha Gen 5. Glock sells its own Performance Trigger by caliber, and the roundup reports that Glock lists the .40 S&W version for the G22, G23 and G27 in Gen4 and Gen5.
Faxon sells a Duty Series 9mm conversion barrel for Glock 22 Gen 2, Gen 3 and Gen 4 slides. Its page says: "Conversion note: run 9mm magazines and a 9mm recoil assembly (guide rod and spring) with this conversion barrel. Neither is included." The product names no Gen5 slide and no Glock 23. No barrel maker's own page we read lists a 9mm conversion barrel for the Glock 23 or for the Gen5 .40 S&W models. Faxon states that it is not affiliated with or endorsed by Glock, and that on some aftermarket slides minor fitting may be needed.
Glock's instructions for use say to use only commercially manufactured ammunition "in the same caliber as your GLOCK pistol", and that the caliber is marked on the pistol's barrel. The same passage says not to use reloaded, remanufactured or handloaded ammunition. The sources we read do not describe what happens if the wrong cartridge is fired. Some owners describe converting a .40 Glock to 9mm as just a barrel swap. Faxon's own note adds 9mm magazines and a 9mm recoil assembly.
Will a Glock 19 holster fit a Glock 23?
Safariland files the Glock 19 and Glock 23 under one holster fit code, 283 ("GLOCK 19/23"). It gives the Gen 5 pair a separate code, 2835 ("GLOCK 19/23 (Gen 5)"). It does the same for the 17/22 and the 26/27. Those codes cover Safariland's own holsters only.
Vedder lists a separate Glock 23 (Gen 5) model, the Glock 23 (Gen 5) IWB Holster RapidTuck. Its page does not say whether a Glock 19 holster fits. Glock lists the slide at 25.5 mm for the G19 Gen5 and 27.5 mm for the G23 Gen5. Its G23 Gen5 page notes: "The slide width of the 40 S&W Gen5 models is slightly bigger compared to the previous generation. Please consider when choosing your holster."
Some holster makers build one fit for both pistols, as Safariland's 19/23 code shows. Others list the Glock 23 Gen 5 as its own model, as Vedder does. Check the holster maker's fit list for your exact model and generation. In our Glock 19 holster guide, the Bianchi 100 and the Galco Tuck-N-Go TUC226 list the Glock 23 with the Glock 19, and so does the Comp-Tac model on its card. The Safariland Incog X on its card is listed for the Glock 17 and 19 only.
For holsters across carry pistols, see our concealed carry holster picks.
How we researched this: cartridge dimensions and pressures come from SAAMI's ANSI/SAAMI Z299.3-2022 standard and C.I.P.'s Tab IV sheets. Load figures come from the ammunition makers' own pages and catalog: Federal, Speer and Hornady. Pistol figures come from the spec pages of Glock, Springfield Armory and Smith & Wesson. Part and holster fit comes from TriggerTech, Apex, a review on Timney's site, Safariland, Vedder and Faxon, and from our own reviews. Penetration history comes from the November 1989 FBI Law Enforcement Bulletin, as digitized by NCJRS. Ranking articles, forums and video comments were read to see what readers ask; no number, date or rule here comes from them. Sources are named in the text, not linked. This is a research summary, not a hands-on test. See our methodology.
FAQ
Is 40 S&W more powerful than 9mm?
Not by pressure: SAAMI lists the same transducer maximum average pressure for standard 9mm Luger and 40 S&W: 350 in its psi/100 column (35,000 psi). The 40 S&W fires the wider bullet. In each maker pair we read from one product line, the 40 S&W load lists the heavier bullet and more muzzle energy from a 4 in test barrel. Federal lists its 180 gr 40 S&W HST at 408 ft-lb and its 124 gr 9mm HST at 364 ft-lb.
How many more rounds does a 9mm Glock hold than a .40?
Two in the G19/G23 and G17/G22 Gen5 pairs and one in the G26/G27 Gen5 pair, as Glock lists them. The G19 Gen5 holds 15 rounds standard and the G23 Gen5 holds 13. The G17 Gen5 holds 17 and the G22 Gen5 holds 15. The G26 Gen5 holds 10 and the G27 Gen5 holds 9. Springfield Armory ships its XD 4" Low Capacity pistol with two 10-round magazines in both calibers.
Does .40 S&W recoil more than 9mm?
Glock says so in words. Its US caliber glossary describes .40 S&W as "Larger and slower than 9mm, with more recoil." That is a description, not a measurement: no maker we read publishes a measured recoil figure for either cartridge. In each Glock Gen5 pair, the .40 S&W pistol is the heavier one as Glock lists it, with or without the magazine.
Will a Glock 19 holster fit a Glock 23?
It depends on the holster maker's fit list. Safariland files the Glock 19 and Glock 23 under one fit code, with a separate code for the Gen 5 pair. Vedder lists a separate Glock 23 (Gen 5) model. Glock says the slide of its 40 S&W Gen5 models is slightly bigger than the previous generation's. Our Glock 19 holster guide shows which of its holsters list the Glock 23.
Is .40 S&W harder on a pistol than 9mm?
None of the maker sources we read publishes a wear, frame-life or parts-life figure by caliber. Glock's instructions for use cover its 9mm and .40 S&W models in one book, with the G22 and G23 in its specification pages. Its cleaning and lubrication schedule names no caliber, and its last item is "at least once a year."
Can you convert a .40 Glock to 9mm, or fire 9mm in it?
Faxon sells a 9mm conversion barrel for Glock 22 Gen 2, Gen 3 and Gen 4 slides and says to run 9mm magazines and a 9mm recoil assembly with it; neither is included. No barrel maker's page we read lists one for the Glock 23 or Gen5 .40 models. Glock's manual says to use ammunition in the same caliber as the pistol, marked on its barrel. Our sources do not describe what happens if the wrong cartridge is fired.
Is there a 40 S&W +P?
SAAMI's Z299.3-2022 standard has no +P entry for 40 S&W. It does list 9mm Luger +P, at a transducer maximum average pressure of 385 in its psi/100 column (38,500 psi). Standard 9mm Luger and 40 S&W both read 350 in the same column (35,000 psi). Across these two cartridges, the 9mm Luger +P is the only +P loading SAAMI lists.
Next: best Glock triggers · best Glock 19 holsters · best concealed carry holsters · best red dots for Glock · lights for the pistol you pick · all guides.