OpticVerdict Independent buying guides
Search OpticVerdict

The best case trimmer

By the OpticVerdict Editorial Team.
Research-based roundup · Updated 2026-10-07

Quick answer: first pick the type. A power trimmer trims, chamfers and deburrs in one pass and suits anyone trimming hundreds of rifle cases; a hand trimmer costs a fraction and suits small batches. The best case trimmer overall is the Hornady High Speed 3-in-1 Power Case Trimmer (around $600): over 2000 RPM, 20 to 338 caliber per Hornady, and Outdoor Life measured an extreme spread of .0025 inch over 30 trimmed cases. The RCBS MatchMaster (around $700) is the runner-up power trimmer, built with Henderson Precision and the most expensive here. For hand trimming, the Hornady Cam-Lock (around $130) has the most reviews here, the Lyman Universal needs no shell holders or collets, and the Lyman E-Zee Trim (around $50) is the cheapest, with a fixed length per pilot. Setting up a bench from scratch? Start with our best reloading press guide; its Lee Challenger kit already includes Lee's Value Trim trimmer.

Brass cases get longer with use (one Cam-Lock reviewer trims "when my casings start to lengthen after reloading several times"), and a trimmer brings them back to length. Every trimmer here does that job; they differ in speed, in whether they also chamfer and deburr the case mouth, and in how they hold the case. Every card names the exact model we checked and uses the maker's own page for specifications (Hornady, RCBS and Lyman), with independent test results where a tester published them. This page publishes no load data or trim lengths.

Which type of case trimmer do you need?

  1. Power 3-in-1 trimmer (Hornady High Speed, RCBS MatchMaster): a motor spins a cutter head that trims, chamfers and deburrs in one pass while you slide the case in. The fastest and the most expensive; GUNS Magazine puts the Hornady at about three seconds per case.
  2. Hand-crank lathe trimmer (Hornady Cam-Lock, Lyman Universal): the case is locked in a holder and you turn a crank to bring it to length. Adjustable for many calibers. Outdoor Life calls this type precise and effective but painstakingly slow, with chamfering and deburring still done by hand.
  3. Pre-set hand trimmer (Lyman E-Zee Trim): each caliber pilot sets the length, so there is nothing to adjust. Turn it by hand or chuck it in a drill. The cheapest way to trim one or two calibers.

This page covers metallic cartridge brass only. For shotshells, see our Hornady 366 Auto review.

Case trimmers compared

TrimmerBest forTypeChamfer and deburrHolds the case withCaliber range (maker or listing)PilotsOpticsPlanet ratingPrice
Hornady High SpeedOverall, volumePowerSame passCollet A or B20 to 338 cal, 1.450 to 3.5 in (Hornady)84.5 (4)around $600
RCBS MatchMasterPower, runner-upPowerSame pass#1 collet22 to 338 cal, 1.460 to 2.870 in (RCBS)75.0 (3)around $700
Hornady Cam-LockManual, many calibersHand crankSeparate (optional Hornady tool)Hornady shell holderUp to 50 cal (Hornady)104.6 (8)around $130
Lyman UniversalManual, no shell holdersHand crankNone listedUniversal Chuckhead, no collets (Lyman).17 to .458 cal (Lyman)94.8 (4)around $170
Lyman E-Zee TrimBudgetHand or drillNone listedStandard shellholderRifle set: .223, .243, .270, 30-06, .308 (Lyman)5 (Rifle set)5.0 (3)around $50

Types, case ranges and pilot counts are from each maker's page, and the Hornady High Speed pilot count is Hornady's current figure. Ratings are OpticsPlanet's, shown with the number of reviews; with 3 to 8 reviews each, they are a small sample. Prices are bands; confirm the current price and availability on the retailer page before you buy.

Our picks

Red and black Hornady motor-driven case trimmer with clear cutter guard (OpticsPlanet listing photo)

Best case trimmer overall: Hornady High Speed 3-in-1 Power Case Trimmer 050190

4.6/5 our editorial score

4.5/5 from 4 reviews on OpticsPlanet (all four from 2026)

Motor driven bench trimmer · trims, chamfers and deburrs in one step · 2000+ RPM · 8 pilots, 2 collets (Hornady) · card: 050190

around $600exact price on OpticsPlanet

Check price on OpticsPlanet

The power trimmer we would point most rifle reloaders to, because it has the strongest independent evidence on this page. Hornady puts trimming, chamfering and deburring into one step on a motor that runs at over 2000 RPM, with a click-adjustable micrometer for length. Hornady's own claim is repeat trims within a +/- .002 inch window with the same lotted brass. Outdoor Life's Tyler Freel, who writes that they received the trimmer that fall, trimmed 30 pieces of 6.5 Creedmoor brass in a row while working quickly: aiming for 1.910 inch, the cases averaged 1.9098 inch, with an extreme spread of .0025 inch and a standard deviation of .0005 inch. GUNS Magazine puts the total time per case at about three seconds, inserting and removing it included. Hornady's current page lists cases from 20 to 338 caliber and 1.450 to 3.5 inches, with 8 pilots. The trade-offs: every caliber change means swapping the pilot, re-seating the blades and resetting depth, and the micrometer clicks can fade with use. One owner (the 3-star review) says the micro-adjust clicks stopped working early, and Outdoor Life saw the clicks lose their positive feel and fixed it with a small Allen set screw.

A Hornady video showing the High Speed Trimmer setting up and trimming rifle cases on the bench, via OpticsPlanet.

Pros

  • Trims, chamfers and deburrs in one step at over 2000 RPM (Hornady)
  • Independent measurement: 30 cases of 6.5 Creedmoor, extreme spread .0025 in, standard deviation .0005 in (Outdoor Life, Tyler Freel)
  • Quiet: Outdoor Life says the motor "runs fast and quietly", GUNS Magazine calls it "absurdly quiet", and one owner writes "The big plus is how quiet it runs."
  • Turn the handle back and the trimmed case drops into a bin, leaving a hand free for the next case (Ultimate Reloader)

Cons

  • Caliber changes are real work: remove the cutter head, change the pilot, re-seat the blades and reset depth, and change the collet if the rim size differs (Outdoor Life, Ultimate Reloader)
  • Micrometer clicks can fade: one owner's "tactile and audible clicks for micro adjust stopped working within the first 200 rds I trimmed"; Outdoor Life fixed the same issue with the small Allen set screw
  • Now and then the collet does not grip and the case spins with the cutter, which Outdoor Life calls a "pretty minor inconvenience"
  • A small review record: 4 reviews on OpticsPlanet, one of them 3 stars

Best for: a rifle reloader who trims hundreds of cases at a time and wants trim, chamfer and deburr done in one pass. If you load one or two calibers in small batches, a hand trimmer below costs far less.

Key specifications
ManufacturerHornady
TypeMotor driven bench trimmer, 3-in-1 (trim, chamfer, deburr)
MotorOver 2000 RPM (Hornady); Hornady also lists a 220 V version, item 050191
Case range20 cal up to 338 cal, 1.450 in to 3.5 in (Hornady's current page; its October 2024 launch announcement and the retailer listing say 22 to 30 caliber)
Pilots8, diameters .20, .22, .24, .25, .26, .28, .30 and .338 (Hornady); Ultimate Reloader's May 2025 unit came with four
Case holdingCollet A, small and standard rifle (.375 and .470 rim); Collet B, ARC and magnum (.438 and .532 rim) (Hornady)
Length adjustmentClick-adjustable micrometer plus a hard stop with 20 detents spaced .20 in apart (Hornady); about .001 in per click (Outdoor Life)
Repeatability+/- .002 in with the same lotted brass (Hornady)
CutterCarbide (Hornady blog); replacement cutter item 480331
WarrantyHornady reloading tools: life of the product, void if used commercially; Hornady electronic components: one year (Hornady warranty FAQ)
Spec sourceHornady's product page, launch release and warranty FAQ, plus the tests named above
Model on this card050190 (UPC 090255501902); the voltage of 050190 is not stated on Hornady's page

“It does take some time to setup, but once set, you can fly through the 100s of cases.”

Kimmers, owner (UT) via OpticsPlanet
Black RCBS motor-driven case trimmer with green handle and bin (OpticsPlanet listing photo)

Runner-up power trimmer: RCBS MatchMaster Precision Case Trimmer 90369

4.4/5 our editorial score

5.0/5 from 3 reviews on OpticsPlanet (all three from 2026)

Motor driven bench trimmer · 3-way carbide cutter · micrometer length stop · 7 pilots, #1 collet (RCBS) · card: 90369

around $700exact price on OpticsPlanet

Check price on OpticsPlanet

The other power trimmer here, and the runner-up: it does the same trim, chamfer and deburr pass as the Hornady, but it costs more, RCBS lists a shorter maximum case length (2.870 against 3.5 inches) and seven pilots against Hornady's eight, and the independent measurement on this page is of the Hornady. RCBS says the MatchMaster is built in collaboration with Henderson Precision, and that its collets interchange with Henderson trimmers while its pilots and cutter heads do not. It has a 3-way carbide cutter that trims, deburrs and chamfers, a high-speed motor and a micrometer length adjustment, and RCBS says it is machined in the USA from 6061-T6 aluminum and stainless steel. RCBS calls it repeatable down to a .001 of an inch; it does not say how that was measured, so we do not set it against Hornady's differently worded +/- .002 inch claim. The box includes seven pilots and the #1 collet, which RCBS says covers 223 Rem, 308 Win, 6.5 CM, 300 Win Mag and others. All 3 reviews are five stars, and one owner writes: "You dial in length on your shortest case and the rest will be precisely the same." It is the most expensive trimmer on this page, and RCBS itself says its cutter heads are too short to easily trim pistol brass.

Pros

  • 3-way carbide cutter trims, deburrs and chamfers in one motion (RCBS)
  • Built in collaboration with Henderson Precision; machined in the USA from 6061-T6 aluminum and 303/416 stainless steel (RCBS)
  • RCBS rates it repeatable down to a .001 of an inch
  • All 3 OpticsPlanet reviews are five stars; one owner lists it as quiet

Cons

  • The most expensive trimmer on this page
  • Case length range 1.460 to 2.870 in (RCBS), shorter than the Hornady's published 3.5 in maximum, and RCBS says its cutter heads are too short to easily trim pistol brass
  • Seven pilots, .22 to .30 cal; RCBS does not include a .338 pilot in the box, and older RCBS Trim Pro pilots, collets and cutter heads do not fit
  • One owner was "missing 2 screws that hold the cover for the shavings" and lists the shavings cover design as the con

Best for: a rifle reloader working mostly in .22 to .30 caliber, the range of its seven included pilots, who wants RCBS's Henderson Precision collaboration (RCBS says Henderson collets fit it) and does not mind paying the most here. For a longer case length range and more included pilots for less, the Hornady above.

Key specifications
ManufacturerRCBS
TypeMotor driven bench trimmer, 3-way carbide cutter (trim, deburr, chamfer)
Case range22 - 338 cal, 1.460 in to 2.870 in (RCBS); the retailer listing says 22 - 30 cal, 1.36 in to 2.85 in
Pilots includedSeven: .22, .24, .25, .26, .27, .28, .30 cal (RCBS)
Collet included#1 collet for 223 Rem, 308 Win, 6.5CM, 300 Win Mag and many others (RCBS); RCBS says collet #1 fits .379, .473 or .532 rims, and that collets interchange with Henderson trimmers (pilots and cutter heads do not)
Length adjustmentMatchMaster micrometer (RCBS)
RepeatabilityRepeatable down to a .001 of an inch (RCBS)
Build6061-T6 aluminum and 303/416 stainless steel, machined in the USA (RCBS)
MountingRCBS Accessory Base Plate or any bench (RCBS)
Package contentsTrimmer, motor, bracket, case bin, cutterhead, seven pilots, #1 collet (RCBS and the retailer listing)
WarrantyRCBS products that need a battery or power cord: one year from purchase, original purchaser (RCBS warranty page)
Model on this card90369 (UPC 850079710115)

“You dial in length on your shortest case and the rest will be precisely the same.”

300 Winny, owner (NV) via OpticsPlanet
Red Hornady lathe-type case trimmer with crank handle and pilots (OpticsPlanet listing photo)

Best hand-crank lathe trimmer: Hornady Cam-Lock Case Trimmer 050140

4.2/5 our editorial score

4.6/5 from 8 reviews on OpticsPlanet (reviews date from 2014 to 2026; two undated)

Hand-crank lathe trimmer · lever case lock · Micro Adjust cutter, .001 in · 10 pilots (Hornady) · card: 050140

around $130exact price on OpticsPlanet

Check price on OpticsPlanet

A hand-crank lathe trimmer, and the one with the most reviews on this page. Hornady's design locks the case in a shell holder with a lever, so it trims to the same length whatever the rim thickness, and the Micro Adjust cutter moves in .001 inch steps without moving the case. The cutting head is tool steel and Hornady says it trims cases up to 50 caliber; ten pilots from 22 to 45 caliber are included. It only trims: chamfering and deburring are a separate step, and Hornady sells an optional Deburr Tool (050147) that mounts in place of the cutter, plus a Power Trimmer Adapter (050145) to drive it with a battery screwdriver. The catch reviewers mention most is the shell holder: Hornady says to use only standard Hornady shell holders, and 3 of 8 reviews raise it. The most helpful review on the listing is a 3-star one from a reviewer who describes themselves as a forty-year machinist and reports .005 inch of shaft clearance and tooling marks; that is one unit, against six five-star reviews.

Pros

  • Lever lock trims to length regardless of rim thickness (Hornady)
  • Micro Adjust cutter: .001 in changes without moving the case (Hornady)
  • Ten pilots included, 22 cal to 45 cal; tool steel head trims cases up to 50 caliber (Hornady)
  • The most reviews on this page, 8, with six at five stars

Cons

  • Hornady shell holders only (Hornady); "It’s not universal as it only fits Hornady shell holders", one owner writes, and 3 of 8 reviews raise it
  • Trims only: chamfer and deburr are a separate step, or an optional Hornady Deburr Tool
  • Hand cranked, so slow for big batches; one owner says it "Definitely requires learning the feel of the tool"
  • A 3-star reviewer who calls themselves a machinist reports loose shaft clearance and rough tooling marks, and would not recommend it

Best for: a reloader who already uses Hornady shell holders and trims modest batches across many calibers, with pilots from 22 to 45 caliber included.

Key specifications
ManufacturerHornady
TypeHand-crank lathe trimmer (trims only)
Case holdingLever cam lock in a standard Hornady shell holder (use only Hornady shell holders and pilots, per Hornady)
Length adjustmentMicro Adjust cutter, .001 in changes (Hornady)
CutterUltra-hard tool steel, replaceable (item 390972); trims cases up to 50 caliber (Hornady)
Pilots includedTen: 22 cal, 6mm, 25 cal, 6.5mm, 270 cal, 7mm, 30 cal, 35 cal, 38 cal, 45 cal (Hornady)
OptionsPower Trimmer Adapter 050145 (battery screwdriver drive); Deburr Tool 050147 (Hornady)
WarrantyHornady reloading tools: life of the product, void if used commercially (Hornady warranty FAQ)
Spec sourceHornady's Cam Lock Trimmer & Pilots page and warranty FAQ
Model on this card050140 (UPC 090255501407)

“I am amazed at how perfect this trimmer cuts each of my brass when needed.”

Rusty, reviewer (OH) via OpticsPlanet
Orange universal case trimmer with collet, crank handle and pilots (OpticsPlanet listing photo)

Best manual trimmer without shell holders: Lyman Universal Case Trimmer with Carbide Cutter and 9 Pilots 7862009

4.1/5 our editorial score

4.8/5 from 4 reviews on OpticsPlanet (dated reviews from 2012 to 2017; one undated)

Hand-crank lathe trimmer · Universal Chuckhead, no collets · carbide cutter head · 9 pilots · .17 to .458 caliber (Lyman) · card: 7862009

around $170exact price on OpticsPlanet

Check price on OpticsPlanet

The manual pick that needs no shell holder or collet. Lyman says its patented Universal Chuckhead handles any case from .17 to .458 caliber with no collets required (the page heading says virtually all cases from .22 to .458), with a carbide cutter head and 9 of the most popular pilots included. The Cam-Lock, by contrast, takes only Hornady shell holders. One reviewer moved from a shell holder trimmer because "Lyman's trimmer uses a universal chuckholder that saves me time, money, and clutter." Another reviewer, who had trimmed only .308 so far, writes that once the length is locked, "you can cut cases to the right length in seconds." It is turned by hand, and neither Lyman's text, the listing nor the reviews mention a chamfer or deburr step. The review record is thin and old: 4 reviews, the newest dated one from 2017, one owner had not used it yet, and one reviewer wonders how long the plastic ball detent that holds the trim position will last.

Pros

  • One reviewer replaced a shell holder trimmer with it and praises its "universal chuckholder"
  • No shell holders or collets to buy: the Universal Chuckhead takes cases from .17 to .458 caliber (Lyman)
  • Carbide cutter head and 9 pilots included (Lyman)
  • 4.8 from 4 reviews on OpticsPlanet, none below four stars
  • One reviewer writes that "cases clip in and lock easily"

Cons

  • Hand cranked, and no chamfer or deburr step is listed
  • One reviewer notes "it uses a plastic ball as a detent to hold the trimming position" and asks how durable it will be
  • One owner plans to bench mount it because "some folks say it is not stable if not mounted"
  • An old, small review record: 4 reviews, the newest dated 2017, and one owner had not used it yet

Best for: a reloader who does not own Hornady shell holders and wants one hand trimmer for many calibers without buying holders or collets. If you already own Hornady shell holders, the Cam-Lock has the larger and newer review record.

Key specifications
ManufacturerLyman
TypeHand-crank lathe trimmer
Case holdingPatented Universal Chuckhead, no collets required (Lyman)
Case rangeAny case from .17 to .458 caliber (Lyman's text and the retailer listing); Lyman's page heading says virtually all cases from .22 to .458
CutterCarbide cutter head (Lyman)
Pilots9 of the most popular pilots included (Lyman); the listing photo shows six
MaterialMetal (retailer spec table)
Spec sourceLyman's Universal Carbide Case Trimmer page and the retailer listing
Model on this card7862009 (UPC 011516720092); the plain Universal Trimmer without carbide is a different Lyman item

“Easy to set up and use. Trims accurate.”

Legacy Reviewer, owner via OpticsPlanet
Hand case trimmer parts: drill adapter, case holder with brass case, cutter with pilot (OpticsPlanet listing photo, set not identifiable)

Best budget case trimmer: Lyman E-Zee Trim Hand Case Trimmer, Rifle Set 7821891

4.0/5 our editorial score

5.0/5 from 3 reviews on OpticsPlanet (listing-wide, all three sets; dated reviews from 2013 and 2014)

Hand or drill powered · pre-set length per caliber pilot · Rifle set: .223, .243, .270, .30-06, .308 (Lyman) · card: 7821891

around $50exact price on OpticsPlanet

Check price on OpticsPlanet

The cheapest trimmer on this page, and a different idea: no length setting at all. Lyman says the E-Zee Trim trims to a precise pre-set length by hand or with a power attachment, which is included, with no adjustment or measuring needed, because each caliber has its own trim-to-length pilot. It works with any standard shellholder, including Lyman, Redding, RCBS, Hornady and Lee. The card is the Rifle set, with pilots for .223, .243, .270, 30-06 and .308; the same listing also offers a Handgun set and a Universal version with no pilots. One owner moved to it after .223 brass kept slipping out of a drill-mounted trimmer and writes, "I've trimmed about 1000 pieces with no problems." All 3 reviews mention a drill. The limits: one fixed length per pilot (Lyman: no adjustment needed), no chamfer or deburr step is listed, and the reviews are listing-wide, the dated ones from 2013 and 2014.

A Lyman video showing the E-Zee Trim hand case trimmer, its rifle and pistol pilot sets, and trimming by hand or with a cordless drill, via OpticsPlanet. The video covers all three E-Zee sets; the card above is the Rifle set, which does not include the pistol pilots.

Pros

  • The lowest price on this page
  • Pre-set length per caliber pilot: no adjustment or measuring needed (Lyman)
  • Hand or drill powered; the power attachment is included (Lyman); all 3 reviews mention using a drill
  • Works with any standard shellholder: Lyman, Redding, RCBS, Hornady and Lee (Lyman)

Cons

  • One fixed length per pilot (Lyman); each caliber needs its own pilot
  • No chamfer or deburr step listed (Lyman)
  • The Rifle set covers five cartridges (Lyman); handgun pilots come in a different set
  • Only 3 reviews, shared across all three sets on the listing, the dated ones from 2013 and 2014

Best for: a new reloader with one or two common rifle cartridges who wants trimmed cases without a bench machine. For many calibers or adjustable length, the Cam-Lock or the Lyman Universal.

Key specifications
ManufacturerLyman
TypeHand trimmer, hand or power (drill) driven
LengthPre-set by the trim-to-length pilot; no adjustment needed (Lyman)
In the systemCase locking device, cutter, trim-to-length pilot, cutter head, hand and power trimming adapters (Lyman)
Shell holdersAny standard shellholder, including Lyman, Redding, RCBS, Hornady and Lee (Lyman)
Rifle set pilots.223, .243, .270, 30-06 and .308 (Lyman)
Weight10 oz (retailer spec table)
Model on this cardRifle set 7821891 (UPC 011516718914); the Handgun set 7821892 and the Universal no-pilot version 7821890 share the listing

“Pre set pilots makes this trimmer easy to set up and use.”

Legacy Reviewer, reviewer (CA) via OpticsPlanet

Two related items share names with the trimmers above. RCBS also sells a MatchMaster powder dispenser, a different product covered in our RCBS MatchMaster powder dispenser review. Lyman's bench kit includes its Universal Trimmer (Lyman's kit list does not name the carbide cutter version carded here), covered in our Lyman Ultimate Reloading System review.

How to choose a case trimmer

A note on safety

This page reviews equipment only and publishes no load data or trim lengths. Take the maximum and trim-to lengths from a current reloading manual or the published data for your cartridge, check trimmed cases with calipers, and wear eye protection at the bench.

How we chose these

This is a research-based roundup, not a hands-on test. We started from the retailer's case trimmer search results and picked two power trimmers and three hand trimmers of different designs. For each we opened the full model list to find the new, orderable model each card links to, and read every review on the listing, including the 3-star ones. We checked specifications against Hornady's, RCBS's and Lyman's own pages. Independent results come from Outdoor Life (Tyler Freel), GUNS Magazine (Frank Jardim) and Ultimate Reloader (Gavin Gear), named as each tester's own result. Claims we could not confirm at the maker or in a published test were left out, including a trade show award, cases-per-minute figures, adjustable chamfer angles and the Hornady's voltage. Our scores are our opinion; retailer ratings are shown attributed to the retailer that collected them. See our methodology for how we work.

FAQ

What is the best case trimmer?

For a rifle reloader trimming in volume, the Hornady High Speed 3-in-1 Power Case Trimmer 050190. It trims, chamfers and deburrs in one step at over 2000 RPM, Hornady lists cases from 20 to 338 caliber, and Outdoor Life measured an extreme spread of .0025 inch over 30 cases of 6.5 Creedmoor. For small batches, a hand trimmer such as the Hornady Cam-Lock or the Lyman E-Zee Trim costs far less.

Is a power case trimmer worth it?

If you trim hundreds of cases at a time, usually yes. GUNS Magazine puts the Hornady at about three seconds per case including loading and unloading, and both power trimmers on this page chamfer and deburr in the same pass. Outdoor Life describes hand-cranked lathe trimmers as precise and effective but painstakingly slow, with chamfering and deburring still done by hand. For a few dozen cases, a hand trimmer does the job.

Do I still need to chamfer and deburr after trimming?

Yes, unless the trimmer does it for you. The Hornady High Speed and the RCBS MatchMaster trim, chamfer and deburr in one step, per their makers. The Hornady Cam-Lock trims only, and Hornady sells an optional Deburr Tool for it; neither Lyman trimmer here lists a chamfer or deburr step.

Hornady High Speed or RCBS MatchMaster: which power trimmer?

Hornady lists a wider range, 20 to 338 caliber and 1.450 to 3.5 inches with 8 pilots, and it costs less. RCBS lists 22 to 338 caliber and 1.460 to 2.870 inches with 7 pilots, and says it is built in collaboration with Henderson Precision. Each maker words its precision claim differently, so we do not rank them on it; the Hornady also has an independent measurement from Outdoor Life.

What else do I need besides the trimmer?

A pilot for each caliber, and the right case holder: a collet on the Hornady High Speed and the RCBS, a standard Hornady shell holder on the Cam-Lock, any standard shellholder on the E-Zee Trim. You also need calipers to check length and the trim-to length from a current reloading manual. OpticVerdict publishes no load data or trim lengths.

OpticVerdict Editorial Team · research-based buying guides

Every award, spec and superlative in this guide is checked against a primary source before it is published, and every rating we cite is shown attributed to where it comes from. Read how we evaluate or learn more about this site.

Source-verified claims Attributed ratings only Method disclosed on every page

More reloading: best reloading press · Hornady 366 Auto review · how we evaluate.