Picatinny or Weaver: what MIL-STD-1913 and the mount makers print about each rail
Quick answer: MIL-STD-1913, the U.S. military standard behind the Picatinny rail, draws the recoil groove .206 in wide. It puts .394 in between the centers of adjacent grooves (Figure 2, inches as printed). There is no matching Weaver figure. Weaver Mounts, the Weaver brand, prints a Weaver slot width of 0.180 in in several articles and 0.156 in in another. We found no published Weaver dimension standard in the sources we searched. On the weaver rail vs picatinny fit question, the makers word the answer differently. Weaver Mounts says an accessory made for traditional Weaver rails "will fit on a Picatinny rail in most cases". Burris says its Xtreme Tactical rings fit "most Weaver and all Picatinny-style mounts". Warne's own blog says any Weaver-style mount works on both Weaver-style and Picatinny rails. Warne, Leupold and Vortex list named rings for both rail types. The other direction is narrower: Weaver Mounts says a Picatinny-only accessory will not fit a traditional Weaver rail "if it has a full-size Picatinny recoil lug". Read the fit line on the exact ring or mount listing and match it to your rail.
Picatinny and Weaver dimensions, as printed
MIL-STD-1913 is titled Dimensioning of Accessory Mounting Rail for Small Arms Weapons. It is dated 3 February 1995, and the U.S. Army is its preparing activity. It defines the rail as "A grooved dovetail feature that serves as a mounting platform used to mount accessories." It defines the recoil groove as a groove "that prevents forward and aft movement of an accessory." It sets its dimensioning and tolerancing "using inch-pound units in lieu of metric", so its Picatinny figures are inches, as printed.
| Item | Picatinny (MIL-STD-1913) | Weaver (as Weaver Mounts prints it) | Source |
|---|---|---|---|
| Slot (groove) width | .206 in, printed .206 +.008 | 0.180 in (Picatinny vs Weaver article and glossary); 0.156 in (Weaver vs Picatinny vs dovetail article) | MIL-STD-1913 Figure 2; Weaver Mounts |
| Slot spacing | .394 in between the centers of adjacent grooves (drawing note 2) | Not standard: varies by model and by maker (Weaver Mounts) | MIL-STD-1913 Figure 2; Weaver Mounts |
| Slot depth | .118 in, printed .118 +.008, from the top of the rail to the groove floor as drawn (the drawing prints no name for it) | 0.100 in (Weaver vs Picatinny vs dovetail article only) | MIL-STD-1913 Figure 2; Weaver Mounts |
| Number of slots | Not fixed: depends on the application (drawing note 1) | Usually fewer cross-slots, sometimes just a couple (Weaver Mounts) | MIL-STD-1913 Figure 2; Weaver Mounts |
| Width across the angled sides | .835 in, the widest horizontal dimension of the profile | No Weaver profile drawing in the sources we read | MIL-STD-1913 Figure 1 (1999 page) |
Weaver Mounts' Picatinny vs Weaver article says "A slot on a traditional Weaver® rail is 0.180 inches wide", and its glossary gives the same 0.180 inches. Its Weaver vs Picatinny vs dovetail article lists a different slot width, 0.156 in. That article also gives a slot depth of 0.100 in. It puts the center of a slot at least 0.406 in from the edge of the base. None of these pages cites a drawing or a standard for its Weaver figures.
The same dovetail article says: "Slot spacing is not standard: spacing varies by model, and Weaver® compatible rails from other manufacturers vary as well." We found no published Weaver dimension standard in the sources we searched. Those were the Weaver brand's own pages, ring and base makers' pages (Warne, and Leupold's fit guide) and the MIL-STD-1913 library. None of them gives a drawing number or a standards body for Weaver bases.
Weaver Mounts' articles also differ on the Picatinny slot: 0.206 in in several, about 0.210 in in another. The standard's drawing prints .206. Some comparisons give the Picatinny spacing as exactly 10 mm. MIL-STD-1913 prints .394 in, and its dimensions are inch only. Millimeter figures for the Picatinny slot seen elsewhere are not printed in the standard.
A 1999 notice replaced the standard's Figure 1 page, the rail profile. Figure 2, the recoil groove drawing, was not among the replaced pages, so its 1995 values stand. The standard fixes no rail length either: it says the length "is dependent upon the particular application" of the weapon it is mounted on.
Do Weaver rings fit a Picatinny rail?
Weaver Mounts' Start Here article puts that question to itself and answers "Usually yes." Its comparison article says an accessory made for traditional Weaver® rails "(mount, ring, etc.) will fit on a Picatinny rail in most cases". A Weaver Mounts guide words it more strictly: "While Weaver and Picatinny mounts are not interchangeable, they share many similarities." The ring makers state fit product by product:
- Warne Maxima 501M (1 inch, medium): "Fits both Picatinny & weaver style bases".
- Warne Mountain Tech 7214M (30mm, medium): "Fits Picatinny & Weaver style mounts and are NATO-STANAG compatible."
- Leupold PRW2 Cross-Slot Rings: "These cross-slot rings work with both Weaver and Picatinny rails."
- Burris XTR Signature Rings: "mount on any Picatinny and most Weaver style rails". Burris Xtreme Tactical Rings: "Fits on most Weaver and all Picatinny-style mounts".
- Vortex Hunter 1-Inch and 30mm Rings: "Mounting to a Picatinny or Weaver type rail". Vortex adds: "We do not recommend the Hunter Rings for use on heavy recoiling rifles."
- Weaver Precision Rings: "compatible with both Weaver or Picatinny-style rails and bases". Weaver Precision Tactical Rings: "fully compatible with Picatinny rails and bases".
Warne's own blog says any Weaver-style mount works on both Weaver-style and Picatinny rails. Burris writes "most Weaver" for both of its ring lines. Weaver Mounts writes "in most cases". Our scope ring picks show which of its rings are Picatinny rings and which also list Weaver rails.
Weaver Mounts explains what can go wrong when the fit is loose: "a narrow bar in a wide slot leaves the ring free to shift fore and aft under recoil". Warne's blog, writing about its own Weaver-style rings, says "there is more forward and back play in a picatinny slot". Warne recommends pushing both rings forward toward the muzzle, and for that reason calls the play in the slot "a moot point". Its Mountain Tech ring instructions give the same step: slide each ring forward until the recoil lug touches the front of the cross slot. None of the makers we read publishes a measured zero shift for a Weaver ring on a Picatinny rail.
Will a Picatinny mount fit a Weaver rail?
Weaver Mounts ties this to the lug: "A Picatinny-only accessory will not fit on a traditional Weaver® rail if it has a full-size Picatinny recoil lug." The same article adds that "lots of products labeled for Picatinny use actually have a small enough crossbolt to work on traditional Weaver® rails". Its Start Here article is stricter about rings: "Picatinny rings will not fit well on a Weaver rail."
Warne's blog says some makers build Picatinny-specific mounts that can only go on a Picatinny rail, and it gives two reasons. The recoil lug may be too wide for the Weaver-style slot. Or the mount may have several lugs spaced for Picatinny slot spacing, which will not line up with the slots on a Weaver-style base. Weaver Mounts' glossary adds that Weaver slot spacing varies by manufacturer: "Weaver rails and accessories aren't always perfectly interchangeable the way Picatinny components are."
Accessory makers name the rails their own products fit. Aimpoint says its Acro Mount 22 mm "Fits on Weaver and Picatinny rail". EOTech's Help Center says its holographic weapon sights have an integral mounting platform "to interface directly with any standard 1 Weaver dovetail or Picatinny Mil spec 1913 mounting rail". That line prints no unit after the 1; EOTech's product pages for the 518, XPS2 and EXPS3 list the mount as a 1 inch Weaver or MIL-STD-1913 rail. Magpul says its MBUS Pro Sight Front "Mounts on any MIL-STD-1913 Picatinny/STANAG 4694 rail including receiver-height gas blocks". Its MBUS 3 Sight Front "Attaches to M1913 Picatinny rails". The Magpul product text we read does not mention Weaver, so it settles nothing for a Weaver rail. Our backup iron sight picks give a mount line for each sight.
Streamlight's fact sheet for the TLR-1 HL says it "Mounts directly to handguns with Glock-style rails and to all MIL-STD-1913 (Picatinny) rails." SureFire says its M600U "attaches to any MIL-STD-1913 rail via its integral thumbscrew clamp". SureFire lists its X300U-A for "both Universal and Picatinny accessory rails". The SureFire text we read does not define Universal, so it should not be read as Weaver. Our rifle light picks give the mount each light comes with.
Harris says its bipods "can attach to the Sling Swivel Stud or a Picatinny Rail", and that "the P models attach directly to a Picatinny Rail". For an older Harris bipod, its FAQ says you can buy an adapter for a Picatinny rail. It names three: the PRA, RBA-1 and RBA-2. Our rifle bipod picks sort bipods by what they mount to.
Some comparisons say a Picatinny accessory never fits a Weaver rail. Weaver Mounts itself makes the answer depend on the size of the lug or crossbolt.
Recoil lugs and cross-bolts
The part of a ring or mount that sits in the rail's groove has several names. Warne calls it a recoil key or a recoil lug. Weaver Mounts calls it a crossbolt, and Seekins an integral center lug. The makers describe it this way:
- Warne Maxima 501M: "Square, permanently installed recoil keys for positive engagement of ring to base."
- Warne Mountain Tech instructions: "Slide each ring forward so the recoil lug is contacting the front of the cross slot."
- Weaver Mounts: "our Four-Hole and Six-Hole Picatinny Rings use a crossbolt built to Picatinny spec, so it fills the slot properly".
- Seekins Precision rings: "Standard 1913 Picatinny standard with integral center lug".
- Nightforce: its Standard Duty Base is "machined from 7075 aluminum to MIL-STD 1913 rail specifications", and its X-Treme Duty steel bases use "exact Mil. Std. 1913 specification rail dimensions".
None of the ring makers we read prints the width of its recoil lug or crossbolt. A lug cannot be checked against the .206 in groove by the numbers, so the maker's fit line is the check.
Torque is set per product as well. Weaver Mounts says: "For rings, there is no single torque spec number. Values differ by family and by fastener." It lists 15 in-lbs for the caps and 48 in-lbs for the crossbolt of its Four-Hole Picatinny rings. For its Precision Tactical rings it lists 25 and 65. Warne gives 65 in/lbs maximum for the Mountain Tech ring nut. Our scope mounting guide covers the torque wrench step.
Dovetail rails: 11 mm, 3/8 in and 13 mm
Weaver Mounts treats dovetail as a third rail type. It says 11 mm and 3/8 in dovetail rails are common on rimfire rifles (.22), airguns and some lighter rifle platforms. It also says a ring made for Picatinny or Weaver rails, put on a dovetail without a proper adapter, can give poor alignment, poor fit or none at all. Its advice is to look for dovetail-specific rings or an adapter that converts a dovetail to a Weaver compatible or Picatinny rail.
Ring makers sell rimfire rings by the dovetail's name:
- Warne Maxima Rimfire 722M: "They fit both 3/8-inch and 11mm dovetails found on many rimfire rifles."
- Leupold sells an RM Rimfire 11mm ring "designed to fit an 11mm rail", and an RM Rimfire 3/8 ring for a 3/8 in rail.
- Leupold's Base and Ring Fit Guide keeps separate rimfire lists for 11mm, 13mm and 3/8 inch dovetail rails.
- Weaver Mounts says its Tip-Off and .22 rings clamp onto 3/8 in or 11mm dovetail rails on rimfires and air rifles.
- Aimpoint lists a "Micro™ 11 mm Dovetail mount for Micro™ sights".
These are sizes in ring and mount listings, not dimensions from a standard. None of the pages we read prints a dovetail width drawing, so the name on your rifle's rail is the thing to match. For an air rifle, Weaver Mounts names airguns among the guns with 11 mm or 3/8 in dovetails.
Which rail is on your rifle?
Weaver Mounts' Weaver vs Picatinny vs dovetail article gives a quick checklist and words each result as likely. Evenly spaced cross-slots of a consistent size point to Picatinny. Just a few slots, narrower and unevenly spaced, point to a Weaver compatible rail. No cross-slots, only continuous angled rail surfaces, point to a dovetail (11 mm or 3/8 in).
The only published rail drawing we found is MIL-STD-1913's. Its Figure 2 prints the .206 in groove width and .394 in between groove centers. For Weaver rails, Weaver Mounts' own articles print a slot width of 0.180 in in some and 0.156 in in another. We found no published drawing for Weaver or dovetail rails in the sources we searched.
Ruger's spec sheet for the 10/22 Standard model 32012 says: "Combination scope base adapter for both Weaver-style and .22 tip-off scope mounts included." For model 32032 it says: "Factory-installed Picatinny rail provides ample room for scopes and red-dot sights." The 10/22 Carbon Fiber model 31231 has an "Integral, optics-ready 30 MOA Picatinny rail". The answer changes with the model number.
Ruger's PC Carbine model 19131 has a receiver with "an integrated Picatinny-style" rail. Its spec sheet adds a condition: "optics and optic mounts that extend more than .275" below the top of the rail may not fit the PC Carbine". Ruger's December 31, 2025 release for its Harrier rifles says: "Each flat-top upper receiver includes Picatinny rail slots". Its model 28600 has "a handguard with a full-length STANAG-spec top rail".
Savage's spec tables for the Axis XP (57256) and Axis II XP (57090) packages list "Scope Bases 2 Piece, Weaver Style". For the REVEL, Savage writes: "The REVEL’s receiver is drilled and tapped for size #6-48 screws". That sentence names no rail type. Read the firearm maker's spec sheet or manual for your exact model number. If it names a rail, match the ring or mount to that name.
Where the names and the standard come from
Weaver Mounts dates the original Weaver rail to "around 1930 by gunsmith William R. Weaver". A Weaver Mounts guide says the Weaver cross-slot system was first introduced in the mid-20th century. Its Our Story page says the company was started in Kentucky in 1930 and moved to El Paso, Texas, in 1933.
MIL-STD-1913 is dated 3 February 1995. Its foreword directs comments on the standard to "Commander, U.S. Army Armament Research, Development and Engineering Center, Attn: SMCAR-QAF-S, Picatinny Arsenal, NJ 07806-5000". Weaver Mounts' Picatinny vs Weaver article says the Picatinny rail was "Developed at the U.S. Army’s Picatinny Arsenal". Notice 1, dated 10 June 1999, replaced page 4, the Figure 1 rail profile. A notice dated 20 April 2004 says the 1999 version "has been reviewed and determined to be valid for use in acquisition". Notice 2, dated 3 October 2013, says the same of the version dated 20 April 2004.
In a slide presentation, Per G. Arvidsson, chairman of the Weapons & Sensors Working Group of the NATO Army Armaments Group, described STANAG 4694, the NATO Accessory Rail. The slide says: "The NATO Accessory Rail has full backwards compatibility with MIL-STD-1913 rail grabbers/mounts." That covers MIL-STD-1913 mounts on the NATO rail; the slide does not say the reverse. Another slide lists a metric drawing among the differences between MIL-STD-1913 and STANAG 4694. Warne and Magpul name STANAG 4694 on the product pages quoted above.
How we researched this: Picatinny dimensions and dates come from MIL-STD-1913 and its notices, read from the copies in the everyspec library. The drawing values were read from the page images, since the drawing carries no text layer. Weaver figures and history come from the Weaver brand's own pages. Fit statements come from the ring, base and accessory makers' own pages, Warne's blog among them: Weaver Mounts, Warne, Leupold, Burris, Vortex, Seekins, Nightforce, Magpul, Streamlight, SureFire, Aimpoint, EOTech and Harris. Firearm rails come from Ruger and Savage. The NATO rail lines come from a slide presentation by the chairman of a NATO Army Armaments Group working group. Other ranking articles, forums and video comments were read to see what readers ask; no number, date or rule here comes from them. Sources are named in the text, not linked. This is a research summary, not a hands-on test. See our methodology.
FAQ
Do Weaver rings fit a Picatinny rail?
Usually, and the makers word it differently. Weaver Mounts answers "Usually yes." Burris says its Xtreme Tactical rings fit "most Weaver and all Picatinny-style mounts". Warne's own blog says any Weaver-style mount works on both Weaver-style and Picatinny rails. Warne, Leupold and Vortex list named rings for both rail types. Weaver Mounts warns that a narrow bar in a wide slot can let a ring shift under recoil, so check the fit line for your exact ring.
Do Picatinny mounts fit a Weaver rail?
Sometimes. Weaver Mounts says a Picatinny-only accessory will not fit a traditional Weaver rail "if it has a full-size Picatinny recoil lug", and that many products labeled for Picatinny use have a crossbolt small enough for Weaver rails. Its Start Here article says Picatinny rings "will not fit well on a Weaver rail." Some mounts list both rails, such as Aimpoint's Acro Mount 22 mm. Check the fit line of the exact mount.
What is the slot width of a Picatinny rail?
MIL-STD-1913 draws the recoil groove .206 in wide, printed as .206 +.008, in its Figure 2. The same figure puts .394 in between the centers of adjacent grooves. The standard specifies inch-pound units for its dimensioning, so these are inch figures as printed. The number of grooves is not fixed: a note on the drawing says it depends on the application.
Is there a Weaver rail standard?
We found no published Weaver dimension standard in the sources we searched: the Weaver brand's own pages, ring and base makers' pages and the MIL-STD-1913 library. None gave a drawing number or a standards body for Weaver bases. Weaver Mounts itself prints a Weaver slot of 0.180 in in several articles and 0.156 in in another, and says Weaver slot spacing is not standard.
What does a dovetail ring need?
A ring sold for the dovetail's named size. Warne says its Maxima Rimfire 722M rings fit 3/8-inch and 11mm dovetails. Leupold sells RM Rimfire rings for an 11mm rail and for a 3/8 in rail, and its fit guide also lists 13mm. Weaver Mounts says a dovetail needs dovetail-specific rings or an adapter that converts it to a Weaver compatible or Picatinny rail.
Why is the Picatinny rail called 1913?
The 1913 is part of the standard's designation, MIL-STD-1913, titled Dimensioning of Accessory Mounting Rail for Small Arms Weapons and prepared by the U.S. Army. Its base document is dated 3 February 1995. A 1999 notice replaced its Figure 1 page. Validation notices dated 20 April 2004 and 3 October 2013 say it was reviewed and determined to be valid for use in acquisition.
Next: best scope rings · how to mount a rifle scope · best backup iron sights · best rifle lights · best rifle bipods · best laser sights · best holographic sights · all guides.